Macbook Pro Won't Boot Fans Not Running Reddit

  • #1

Hey everyone, sol I purchased a 2009 4,1 Mac Pro (Dual x5550) on Craigslist a brace weeks ago for $150. Frankly insane deal for how good of condition it's in. I painlessly flashed information technology to a 5,1, installed High Scomberomorus sierra, upgraded to 32gb of Cram, and installed a GTX 1070. I've had absolutely no problems with IT in the least until go night. It was sleeping and I went to wake IT up aside pressure the spacebar on the keyboard and the powdery on the front man of the case fitting turned off, no noises or anything. Information technology wouldn't flush up at all after that.

So I started troubleshooting. I unplugged the power cord (concisely saw the ruby-red diag CPU LEDs garish) for 15 seconds then plugged IT back in (CPU LEDs flashed again, but for a little longer), tried booting it up then again over again nothing happened. No click sounds, absolutely no signs of life. I past removed all HDDs, Optical drives, artwork card, and replaced the RAM with what the Mac Pro originally came with. I tried booting it functioning and once once more zip happened. I then pressed the DIAG button and I make out visualise the 5V STBY light up.

Nothing I did seemed to desex the trouble, so I essentially gave up and unexpended the Mac unplugged all night. About 20 hours later (now), I decided I would try and see if it would miraculously bi along, so I obstructed the power cable in, pressed the button and the white light on the presence of the slip steamy and I heard a dog... for roughly a indorse so it shut off again. Now nothing I answer will turn information technology on again.

Could someone possibly precede Maine in the right direction Eastern Samoa to what part may glucinium the culprit here? I truly father't want to take it to a Mackintosh Pro Specialist here in LA to get onto diagnosed, and I for sure wear't want to corrupt a Power Cater on a whim and trust that's the job. Any help would be greatly appreciated, thanks!

  • #3

Hey there,

DId you take out the 1070 and replace with original graphics bill that the mac pro came with?

  • #4

Unsure if this is of any benefit, however just just in case (also unsure if the 2009 differs from the 2007 & 2008)...

Source: https://www.ifixit.com/Guide/iMac+Intel+24-Edge+EMC+2134+and+2211+Diagnostic+LED's/7443

Not sure how corresponding the diagnosis LEDs are from the iMac and Mac Pro, simply if they are like and so it would seem as though my power supply is at fault here considering no LEDs are powered on when the power cable is plugged in.

Hey there,

DId you take out the 1070 and substitute with original graphics card that the mac in favour of came with?

Yeah, I tried that simply still no dice :/

  • #5

Whip the hard turn back, and the 1070 and maybe antitrust keep two sticks of ram in. Put the original nontextual matter bill of fare in and try & boot then. It won't boot, evidently, merely it should come up with the flashing folder (hopefully) - at least that'll show the PS is satisfactory.

  • #6

Just to preface this answer, my Mackintosh In favour of has been unplugged all night up until trying what you reasonable suggested.

So I did as you said, left two sticks of RAM in, replaced the 1070 with the archetype GPU, and took out completely hard drives. I then plugged in the power cable and tried booting it functioning. It shortly acted as if it was booting up (scheme fans spun at full speed, along with the GPU fan, and DIAG LEDs afire up) and then stopped. Each of the fans obstructed, but strangely adequate, the OVTMP CPUA red Light-emitting diode stayed lit. Pressing the power button again did nothing to the system, that red LED was stuck like that until I unplugged power line.

I then waited a minute of arc, plugged the power cable back down in, and tried booting again to encounter if I could replicate that result, but again dead nothing happened when pressing the magnate clit, but muteness. I snapped a delineation of the LED lit in the lead since I had the bump.

  • 20180213_093601.jpg

    20180213_093601.jpg

    1,004.2 KB · Views: 328

  • #7

Okay, that picture says a lot..

Condemned from the 2009 Mac In favor Techician guide:

"Central processor Diagnostic LEDs
The 8-Congress of Racial Equality and musculus quadriceps femoris-core riser boards include a identification LED for each C.P.U. that you
can use in troubleshooting processor issues. The following illustrations testify the placement of
from each one Light-emitting diode and its connected processor. These error LEDs are normally off. A red illuminated LED
indicates the related to processor may be missing operating theater in overtemp state (PROCHOT).

Troubleshooting CPU Diagnostic LEDs
Determine if the error LED follows the processor heatsink; affirm the heatsink is physically
unmutilated and properly connected to the processor control panel, check that adequate thermal
grease is applied, and verify the fan is operative. For 8 core riser boards only: determine if the
error LED follows the processor by swapping processor A and processor B locations."

Also, IT could related to the known issue of the Northbridge heatsink crop

https://forums.macrumors.com/threads/cmp-4-1-northbridge-temp-high.1926995/

Promise this helps,

Razzerman

  • #8

Okay, that mental picture says a lot..

Assumed from the 2009 Mack Pro Techician guide:

"Processor Diagnostic LEDs
The 8-core and quad-core riser boards include a diagnostic LED for for each one processor that you
can use in troubleshooting processor issues. The following illustrations show the location of
each LED and its associated central processing unit. These erroneous belief LEDs are commonly turned. A red lit LED
indicates the associated processor may embody absent OR in overtemp posit (PROCHOT).

Troubleshooting Processor Diagnostic LEDs
Determine if the mistake LED follows the processor heatsink; verify the heatsink is physically
undamaged and properly connected to the processor board, check that adequate thermal
grease is practical, and verify the fan is operating. For 8 core riser pipeline boards entirely: determine if the
error LED follows the processor aside swapping processor A and processor B locations."

Besides, it could related to the famous publish of the Northbridge heatsink clip

https://forums.macrumors.com/duds/cmp-4-1-northbridge-temp-high.1926995/

Bob Hope this helps,

Razzerman

Thanks, Razzerman! I'll unquestionably check out the riser board on with the Northbridge heatsink when I get internal from work later. I hope the Northbridge heatsink is the culprit since that seems the likes of a comparatively trivial thing to fix. I'll celebrate this thread updated with my findings!

  • #9

So afterward inspection of my riser board, I couldn't seem to find anything tabu of order. Northbridge heatsink clips seem to be intact and jolly sturdy, and swapping the CPUs (A -> B and B -> A) didn't seem to change anything. I'm seeing a recurring pattern here though. All metre I try to the boot upwards the Mac after going IT completely unplugged for 12+ hours, I seem to get some liveliness out of it very briefly (few seconds), but upon trying to boot again later on that first sign of life, it goes backward to being completely dead. Wouldn't this embody a sign in of major power supply condenser nonstarter?

  • #10

Ouch...that's disappointing. Back to second power one then :(

You may have got to bite the smoke and get a PSU. I'd consider it that if it didn't work, you could resell the PSU for a few bucks less, and not much lost. And if it is the PSU, the machine was a really nice terms in the beginning. Some places might even take the old PSU for refurbishment.

  • #12

Aloha State there, good wanted to know whether you could figure out what was wrong with your mac. Though my guess is its a failed PSU, it can be the backplane too. Delight keep us informed. Thanks.

  • #13

Also, take a view this - sounds a bit similar.

https://discussions.apple.com/thread/7812732


Hawaii there, just wanted to know whether you could figure out what was wrong with your mac. Though my guess is its a failed PSU, it ass be the backplane too. Please prevent us informed. Thanks.

So, I finally got or so to purchasing a PSU from eBay from a very reputable seller World Health Organization claims information technology was only misused for a few months in total. Patc I was trying to move out the screws to contract to the current PSU, I completely empty one of them to the point where it's completely impractical to cotton on out, the head is practically just a circle. So I went ahead and arranged a screw removal outfit on Amazon in enjoin to catch on out.

I pretty much gave up at that point and thought "what the hell wherefore not just assay to plug in the new PSU to at to the lowest degree see if that's the problem?" (probably what I should have done in the inaugural place). And so I removed the current PSU's connector and plugged in the new-sprung PSU and still... I get no kick :( The cherry LEDs blip for a second and the diagnostic push gives me the same old 5V STBY Light-emitting diode light. Not too sure what else to do at this power point.

Last edited:

  • #14

Looks like your best bet is to sell it for spares/repairs, and insure if the seller will repossess the 'new' psu.

Disconsolate it hasn't worked out well for you & your machine.

  • #15

Thus, I finally got roughly to purchasing a PSU from eBay from a very honorable seller who claims it was only misused for a few months in total. While I was trying to remove the screws to puzzle over to the current PSU, I completely unclothed extraordinary of them to the point in time where information technology's completely unacceptable to cotton on out, the channelise is much just a roundabout. So I went ahead and ordered a screw removal kit on Amazon in gild to cotton on out.

I pretty much gave up at that point and thought "what the hell why non hardly try to secure in the new PSU to at least see if that's the problem?" (credibly what I should have done in the first off place). So I removed the current PSU's connecter and plugged in the new PSU and still... I father no boot :( The red LEDs blip for a second and the designation button gives Pine Tree State the same white-livered 5V STBY LED light. Non too sure what else to do at this stop.

If you have an Apple authoritative Robert William Service cernter, try and get it diagnosed. It can constitute the backplane or the cpu tray. Only once you have it pin pointed, it testament constitute easier to fix.

  • #16

UPDATE: So I just finished moving to a freshly apartment. This is afterward having not through with anything to the Mackintosh since the last time I posted about unsuccessfully nerve-racking a new power supply. I thought process "Inferno why non try to plug IT in and see if it powers connected?". So I did. And it powered on the moment I obstructed in the power cable! I didn't flatbottomed press the power button. Fans came along normally, hard drives spun dormie, and I heard the chime sound indicating that it had successfully booted!

I let information technology run for a couple of proceedings and so proceeded to turn it cancelled and move it to my monitor and so I could hopefully fix into the system. Sadly, it volition no more bring up up again. On the upside though, doesn't this mean there isn't anything wrong with the processor tray, processors, RAM, or power supply? I'm starting to believe it has something to do with the power button at this point if everything booted up the right way.

Last edited:

  • #18

If you suspect information technology's the power button. Afterwards SMC reset, you can try this. View attachment 757287

So I tested jumping the PWR pads as instructed from the troubleshooting manual and the Mac didn't top executive on. So it looks like the backplane is the perpetrator and not the power button. I went in advance and ordered a replacement backplane from dncomputers.ws. Luckily they provide a 30-day return for some argue. I'll keep you guys updated!

  • #20

UPDATE: IT'S Revived!

Soh afterwards receiving, and installing, the raw backplane, the Mac boots up successfully and I can turn it off... And turn it back on!

I'm now in the process of at length installing Sierra Nevada Mountains on my Samsung SM-951 that I received months ago, the night everything stopped working for me.

So I conjecture if there's anyone out there that has had the exact same troubles as Maine, I would just burn the bullet on a backplane. That is if you put as little money as I did into getting the Mac Pro in the first place. Otherwise it might equal a far more difficult oral contraceptive to eat u.

  • #21

Wow, praise for sticking with information technology and acquiring it working. Nice job! :)

  • #23

Lol thanks guys!

Then a rather gothic development has happened on my conclusion when difficult to install MacOS onto my SM951 (MZVPV256HDGL-00000) with my Lycom adapter. I installed the adapter into one-armed bandit 3 and Disk Utility does in fact detect the drive as an external volume, which from what I've read is normal. I formatted the drive to APFS and started the High Sierra installation process.

Upon finishing the first installation and rebooting, the Mac just refuses to boot to the drive. Even when I go to the Inauguration Disk substitute in recovery, information technology shows nothing there, as if it's not detected as a bootable drive away. The record is even detected in Magnetic disc Utility and shows ~5gb of used place. I as wel tried whol opposite PCI-E slots only to get the exact same result. I even tried some other NGFF adapter (Silverstone ECM22) that I had laying around and still get the same result.

I'm a bit puzzled by this and I can't seem to find much existing advice on the forums about much a job. Any tips?

Last edited:

  • #25

You posterior't kicking from a NVMe SSD

Damn, I totally overlooked that one alphabetic character when I placed the say. No wonder I thought I got IT for such a skillful deal on eBay lol looks like I'll constitute creating a new eBay listing tonight

Last emended:

Macbook Pro Won't Boot Fans Not Running Reddit

Source: https://forums.macrumors.com/threads/2009-mac-pro-suddenly-wont-power-up-anymore.2105863/

0 Komentar

Post a Comment




banner